Carrier-access Access Navigator Manual de usuario Pagina 96
- Pagina / 704
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
5-14 August 2003 Access Navigator - Release 1.8
Physical Installation
Attach Access Navigator to Crossbars
Figure 5-8. Bracket Installation
Figure 5-9. Spacing Requirements
Mount bracket here
for flush mount.
Mounting
Brackets
Mount bracket here for
5 inch forward offset.
Fasten brackets to
Access Navigator
with 6-32 x 3/8"
undercut screws
(four per side).
C
A
D
Fasten brackets to
crossbar with
12-24 x 5/8 inch
machine screws
(two per side).
B
19-inch Equipment Rack
(5 units per row maximum)
23-inch Equipment Rack
(6 units per row maximum)
1.75 inch
Bracket spacing
0.75 inch
Minimum air space
ABCDE ABCDEF
1.75
17.25
- Access Navigator 1
- In this Preface 3
- Compliance 4
- Title and Risk 6
- Copyright 7
- Warranty 7
- Disclaimer 7
- Limitation of Liability 7
- Jurisdiction and Venue 8
- Warranty Product Returns 10
- TABLE OF CONTENTS 11
- Table of Contents 12
- Table of Contents 13
- 5 Physical Installation 14
- 6 Electrical Installation 14
- 7 Start Management Session 17
- 8 Provision Access Navigator 17
- 9 Provision DCS Service 17
- 10 Provision GR-303 Service 18
- 14 Alarm Clearing 20
- 16 Maintenance Procedures 22
- 18 CLI Language Reference 23
- A EOC Interface 27
- B FDL Interface 28
- C SNMP Interface 28
- Introduction 29
- Overview 30
- Features and Benefits 31
- System Architecture 32
- Access Banks 33
- Management 34
- Introduction 35
- Configuration 42
- Applications 43
- Interfaces 43
- Specifications 43
- System Clocking 44
- Signaling 44
- Management Interfaces 44
- Protocols 44
- Environmental 45
- Physical 45
- Compliance Requirements 46
- UL Requirements 47
- Ordering Information 48
- GR-303 Services 52
- DCS Services 54
- Management Architecture 55
- FDL Management 56
- GR-303 Signaling 60
- DCS Signaling 60
- P-Phone Services 70
- Standards 78
- PLUG-IN CIRCUIT CARDS 85
- Horizontal 19-Inch Rack Mount 86
- Horizontal 23-Inch Rack Mount 89
- Install Crossbars 94
- Vertical Wall Mount 97
- Ensure Adequate Clearance 98
- Prepare Plywood 98
- Physical Installation 100
- Physical Installation 101
- Electrical Installation 105
- Electrical Installation 107
- Tools and Materials Required 108
- Chassis Ground Connection 109
- REAR PANEL TERMINALS 111
- DSX-1 Cable Connections 112
- Tools and Materials 113
- Prepare DSX-1 Cables 113
- Attach Ferrite Beads 117
- PREMISES 118
- RS-232 Management Connection 121
- Connect Shielded RS-232 Cable 123
- Preconfigure Optional Modem 125
- Installation Summary 126
- Information and Materials 126
- Make BITS Cable (Optional) 130
- Connect BITS Cable 130
- Alarm Output Connections 131
- Wire Alarm Output Connector 132
- Alarm Input Connections 135
- Wire Alarm Input Connector 136
- DC Power Connections 139
- Wire Power Connectors 140
- Verify Wiring 141
- Dress Cables and Wires 142
- Acceptance Test 143
- Verify DSX-1 Connections 145
- Verify BITS Connection 148
- Exit Management Session 152
- Precautions 153
- Verify Software Compatibility 154
- Remove Front Cover 155
- Install Controller Card 156
- Verify Operation 157
- Replace Front Cover 158
- Install Quad T1 Framer Card 161
- Setup Summary 165
- Set Date 167
- Set Time 167
- Set System ID or CLLI code 168
- Set Gateway Address 169
- Start Management Session 171
- Management Requirements 172
- Start Management Session 173
- RS-232 Management 174
- Obtain Information 175
- Set Up Terminal Program 175
- Perform Management Operations 177
- Telnet Management 178
- Provision Access Navigator 183
- Basic Provisioning Overview 184
- Provision Access Navigator 185
- Set System ID or CLLI Code 187
- Set Ethernet Properties 189
- Set SNMP Properties 193
- Provision DCS Service 195
- DCS Provisioning Overview 196
- Provisioning ISDN BRI Service 197
- Special TR-08 Settings 199
- DCS Provisioning Quick Guide 200
- Provision DCS Service 201
- Verify Service Status 202
- Set System Clock Source 205
- Test Groom DS1 Circuits 208
- Provision and Connect DS0s 211
- Turn Up Service 213
- Test DS1 and DS0 Circuits 213
- Provision GR-303 Service 215
- GR-303 Provisioning Overview 216
- Provision GR-303 Service 217
- Provisioning P-Phone Service 218
- TR-08 Configuration 220
- Special POTS Cards 220
- Signaling Translation 220
- CRV Numbering 220
- Framing and FDL Settings 222
- Set System Switch Type 228
- Test DS1 Circuits 234
- Provision DS0s to Subscribers 244
- Test Circuits 248
- In this Chapter 249
- Pre-Provisioning and Testing 251
- Requirements 251
- Analog Interfaces 252
- Crossconnect Features 252
- FX Analog Interfaces 254
- Fractional Interfaces 255
- Remote Interfaces 256
- Provision DS0s 265
- Provision DS0 Crossconnects 267
- Test Remote Circuits 278
- ADIT 6 00 280
- FDL Management Configuration 281
- CLI Commands Descriptions 283
- Provision Drop DS0s 291
- Provision Remote Adit 600 295
- CACTUS.lite 298
- Adit 600 299
- Navigator 299
- Alarm Clearing 321
- Clear Alarms – FDL 323
- Alarm Clearing 325
- Clear Alarms – EOC 328
- Clear Alarms – SNMP 334
- Critical, Major, Minor 335
- Alarm Indicators 335
- Power Status LEDs 336
- Critical Alarm Status LEDs 338
- Major Alarm Status LEDs 338
- Minor Alarm Status LEDs 339
- Alarm Cutoff (ACO) Status LED 339
- DS1 Status LEDs 340
- Ethernet Link Status LED 341
- Alarms and Logs 344
- Alarm Reporting 345
- Alarm Testing 345
- Alarm and Status Indicators 345
- Facility Alarm System 346
- Alarm Cutoff (ACO) 346
- DS1 Failures 347
- Event Log 347
- Configuration Change Log 348
- Syntax: log bert 349
- Syntax: clear bert log 349
- Syntax: log tmc 349
- Syntax: log tmc permanent 349
- Ethernet 351
- Connector 351
- Ethernet Link OK 351
- Status Indicator 351
- Indicator Descriptions 352
- Syntax: status clock 353
- Message: 353
- Description: 353
- Example: status ds0 32:1-4 354
- Syntax: status ds1 <n> 355
- Example: status ds1 12 355
- Example: status ds1 1-4 355
- Syntax: status ds1 all 356
- Syntax: status equipment 361
- Syntax: show ip 362
- Syntax: status ip 362
- Status Remote 363
- Example: status crv 10 364
- Example: status crv 5-8 364
- Example: status isdn crv 6 365
- Example: status isdn crv 1-4 365
- Syntax: status eoc 367
- Syntax: status tmc 367
- Example: status tmc all 369
- Example: status tmc 8-12 369
- Syntax: clear peak call count 370
- Near-End Loopbacks 371
- DS1 Line Loopback 372
- DS1 Payload Loopback 372
- DS1 CSU Loopup 373
- DS1 Line Loopup 374
- DS1 Network Loopup 375
- DS1 NIU Loopup 376
- DS1 Payload Loopup 377
- Access Bank II Loopbacks 378
- Send Remote RS232 Line Loopup 379
- Send Remote T1 Payload Loopup 381
- Send Remote T1 TSI Loopup 381
- Send Remote V35 Line Loopup 383
- Bit Patterns and Error Tests 385
- Send DS1 Payload Pattern 386
- Other Maintenance Commands 395
- Technical Support 397
- Maintenance Procedures 399
- Repair and Return Procedure 400
- Replace Controller Card 401
- Verify Equipment Status 403
- Procedure Summary 404
- Verify Compatibility 405
- Controller A Controller B 407
- ALTER PROVISIONING 409
- Replace Other Controller Card 410
- Insert New Controller 414
- Maintenance Procedures 415
- Remove Old Controller 416
- Replace Quad T1 Framer Card 417
- Replace Quad T1 Card 421
- INSTALL SIMM 438
- UPDATE SOFTWARE 440
- Verify IP Connectivity 441
- Upload Configuration 441
- Download Software 442
- ANY USER 443
- Download Configuration 444
- NOT ASSIGNED TO ANY USER 449
- CLI Language Reference 457
- CLI Requirements 459
- CLI over Telnet 460
- Using CLI Command Scripts 461
- CLI Conventions and Shortcuts 462
- Text Conventions 463
- Command Syntax Descriptions 464
- Command Shortcuts (Tabbing) 465
- Keyboard Shortcuts 465
- Help System Overview 466
- Displaying Basic Commands 466
- Context Sensitive Help 467
- Syntax: print help 469
- Users and Passwords 470
- Syntax: whoami 471
- Syntax: show users 471
- Set User Password 473
- Delete User Password 473
- Delete User 473
- Logging In and Out 474
- Login with User Name Required 475
- Login with Password Required 475
- Example: set autoexit 60 476
- CLI Command List 477
- CLI Language Reference 478
- Security: Level 3 (monitor) 479
- Syntax: aco 479
- Security: Level 2 (operator) 480
- Add User 481
- Clear BERT Log 483
- Clear Blocked Call Count 483
- Clear Config Log 483
- Clear DS1 Performance 483
- Clear Log 484
- Clear Peak Call Count 484
- Clear Permanent Call Count 484
- Clear Remote Log 484
- Clear TMC Log 484
- Connect Remote Interface 487
- Delete Interface 488
- Disconnect 489
- Disconnect Remote 490
- Exit Remote Session (Ctrl+C) 490
- ON page 17-1 491
- ALL ON page 18-57) 493
- Example: log ds1 6 495
- Example: log equipment minor 495
- Example: log 495
- Log Config 497
- Example: log config 498
- Example: logon remote 12 500
- Read Remote Alarms 501
- Example: read remote 9 log 506
- Read Remote Loopback 507
- Read Remote RS232 507
- Read Remote T1 510
- Example: read remote 9 t1drop 511
- Read Remote V35 512
- Reset All 513
- Reset DS1 Framer 513
- Reset Remote 514
- Reset Standby 514
- Security: Level 1 (manager) 515
- Syntax: restore defaults 515
- Send DS1 CSU Loopup 518
- Send DS1 Line Loopup 519
- Example: set ds1 9 line p2e15 523
- Send DS1 NIU Loopup 527
- Send DS1 Payload Loopup 529
- Example: set ds1 9 down 533
- Send DS1 Off 537
- Send Remote Loopdown 537
- Send Remote RS232 TSI Loopup 539
- Send Remote T1Drop TSI Loopup 546
- Send Remote V35 TSI Loopup 549
- Send Switch Provision Request 550
- Set Alarms 551
- Set Autoexit 551
- Set Clock 552
- Example: set ds0 5:13 crv 122 555
- Set DS0 ISDN BRI CRV 557
- Set DS0 P-Phone 558
- Example: set ds0 13:1-16 up 559
- Set DS1 Clock 562
- Set DS1 FDL 562
- Set DS1 Framing 564
- Set DS1 ID 565
- Set DS1 LBO 565
- Set DS1 Line Loopup 565
- Set DS1 Linecode 566
- Set DS1 Remote Device Mgmt 569
- Set DS1 Service 570
- Set DS1 TermID 570
- Set DS1 Threshold 571
- Set Ethernet IP Address 573
- Set IP Gateway Address 574
- Example: set ip gateway none 575
- Set Remote ID 576
- Set Remote RS232 Baud 576
- Set Remote RS232 Data 577
- Set Remote RS232 Stop 577
- Set Remote T1Drop LBO 579
- Set Remote T1Drop Linecode 579
- Set Remote T1Drop PRM 580
- Set Remote V35 ClockInv 580
- Set Remote V35 CTS 581
- Set Remote V35 Data 581
- Set Remote V35 DSU 582
- Set Remote V35 RxClock 582
- Set Remote V35 Speed 582
- Set Screen 583
- Set SNMP Contact 584
- Set SNMP GetCom 584
- Set SNMP Location 585
- Set SNMP Name 585
- Set SNMP NMS Address 586
- Set SNMP SetCom 586
- Set SNMP TrapCom 587
- Set Switch Type 587
- Set User Level 589
- Show Autoexit 591
- Show Clock 591
- Show Connect 591
- Show CRV 593
- Show Date 595
- Show DS0 595
- Show DS1 596
- Syntax: show ds1 all 599
- Show EOC 601
- Show Ethernet 601
- Show Interface 602
- Show ISDN CRV 604
- Example: show isdn crv 6 605
- Example: show isdn crv 1-8 605
- Show Remote 606
- Show SNMP 609
- Show Switch 610
- Show Time 610
- Show TMC 610
- Status CRV 613
- Status DS0 614
- Status DS1 615
- Status DS1 Performance 618
- Status Equipment 624
- Example: status equipment all 625
- Status ISDN CRV 627
- TMC Status: 629
- Primary 629
- Link Status: Up 629
- Status TMC History 631
- Syntax: switch controller 632
- APPENDIX 635
- EOC Interface 637
- Managed Object Class Support 638
- Alarm Count List Objects 639
- DS1 Line Termination Objects 641
- EBS Line Termination Objects 641
- ISDN Line Termination Objects 642
- Crossconnection 644
- Equipment Objects 645
- IDLC Terminal Objects 648
- Memory Objects 648
- Network Element Objects 649
- Protection Group Objects 649
- Protection Group Unit Objects 650
- Table A-20 Action Support 651
- Notifications 652
- FDL Interface 655
- Access Bank II Capabilities 656
- Carrier Access Enterprise MIB 661
- SNMP Basics 662
- MIB Tables 663
- Managing Networks 664
- SNMP Protocols 665
- SNMP Requirements 666
- SNMP Trap Reports 667
- SNMP Interface 668
- GLOSSARY 669
- Definitions 672
- Glossary 682
- Numerics 683
Relacionado con productos y manuales para Hardware Carrier-access Access Navigator
Hardware Carrier-access 770-0015 AM Manual de usuario
(250 paginas)
(250 paginas)
Hardware Carrier-access Adit 3000 Series and Multi-Service Router (MSR) Ca Manual de usuario
(496 paginas)
(496 paginas)
Hardware Carrier-access Adit 3200 Manual de usuario
(28 paginas)
(28 paginas)
Hardware Carrier-access Adit 3104 Manual de usuario
(74 paginas)
(74 paginas)
Hardware Carrier-access Multi-Service Router (MSR) Card MSR/Adit 3K GUI Manual de usuario
(262 paginas)
(262 paginas)
Hardware Carrier-access Broadmore 1750 Manual de usuario
(420 paginas)
(420 paginas)
Hardware Carrier-access Adit 3500 Manual de usuario
(52 paginas)
(52 paginas)
Hardware Carrier-access CMG Router Manual de usuario
(296 paginas)
(296 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.099 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales