Carrier Access Network Device Axxius 800 Manual de usuario Pagina 470
- Pagina / 568
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
15-18 Axxius 800 - Release 2.2
Terminal Server Router Card
Connector Pinout
TSR Card Jumpers
The jumpers on the TSR card select the use of the 10/100Base-T (RJ-45) or RS-232.
There is one jumper for each port on the card. Each jumper can be set to
10/100Base-T or RS-232, independent of the others.
In the following graphic all port jumpers are set to 10/100Base-T Ethernet.
Connector Placement
10/100Base-T Position is farthest away from the front of the card
RS-232 Position closest to the front of the card
Card Front
- USER MANUAL 1
- Compliance 3
- Port: FIC: SOC: Jack: 4
- Industry Canada CS-03 5
- Industry Canada ICES-003 5
- Safety Information 6
- Preface 7
- Warranty 9
- Warranty Product Returns 10
- TABLE OF CONTENTS 11
- Table of Contents 12
- 4 Configuration 13
- 2 Physical Installation 13
- 5 CLI Commands 14
- Table of Contents 15
- 6 DS1 Controller Card 22
- 7 DS3 Controller Card 22
- 8 FXO Voice Card 23
- 9 ISDN BRI Card 24
- 10 OCU-DP Card 24
- 11 Single Channel POTS Cards 25
- 12 Power Supply 26
- 13 Quad DS1 ADPCM Card 26
- Terminal Server Router Card 28
- 16 V.35/.54 Card 29
- 17 Low Speed Protection Card 29
- 18 Maintenance 30
- A Regulatory Approvals 30
- B SNMP Interface 30
- C Loopback Tests 31
- Base Platform 33
- Overview 34
- Features 35
- Controllers 36
- Service Cards 36
- Base Platform 37
- Power Supplies 38
- Capacities 39
- Redundancy 39
- Control Panel Interfaces 39
- Rear Chassis Interfaces 39
- Axxius 800 - Release 2.2 1-9 41
- Management Ports 42
- Local and Remote Management 42
- DS1 Connection Ports 45
- 10/100Base-T Ethernet 45
- Control Panel LEDs 47
- Ethernet LEDs 48
- Physical Installation 51
- Unpacking and Inspection 52
- Installation Environment 53
- Assembly of Axxius 800 54
- Rack Mounting 55
- Compliant Installation 58
- Ferrite Beads 59
- Chassis Connections 60
- Chassis Ground Connector 62
- Power Connections 63
- 3-8 Axxius 800 - Release 2.2 64
- External Alarm Inputs 65
- Visible and Audible Alarms 66
- BITS Clock 1/BITS Clock 2 67
- Wire-Wrap Connectors 68
- Wire-Wrap Pins Description 70
- Standard Telco Color Code 71
- Setting up a CLI Connection 74
- System Information 75
- Basic System Setup 76
- Set Up Security 77
- Set Up a DS0/Channel 78
- Set Up a DS1/T1 78
- Set Up a DS3 79
- Setup of ADPCM 81
- Set Up a V.35 Port 81
- NTER]) 83
- from the menu bar 84
- Configuration 85
- Equipment Required 87
- Set IP Configuration of PC 89
- Configuring the Axxius Router 89
- AB]) and select [ENTER] 90
- NTER] 91
- [ENTER] 92
- Reinitialize the Router 97
- Command Description 98
- Configuration 100
- CLI Commands 101
- Command Line Interface Help 102
- (13 bits) 116
- [minute-offset] 214
- 310
- Display Descriptions 331
- DS1 Controller Card 363
- Technical Specifications 366
- Management 367
- DS1 Interface 367
- Service Interfaces Supported 368
- Network Standards 368
- Clocking 368
- Testing and Diagnostics 369
- Power Consumption 369
- Environment 369
- Physical 369
- Controller Active and Standby 370
- Built-In Card Handles 372
- DS3 Controller Card 373
- Network DS3 Interface 376
- Controller and DS3 Redundancy 380
- DS3 Controller Card 381
- Network Protection Mode 382
- FXO Voice Card 385
- FXO Signaling Performance 388
- Card Configuration 389
- DIP Switch Settings 390
- Conversions 391
- ISDN BRI Card 393
- Connector Pinouts 400
- OCU-DP Card 401
- Customer Premise Application 403
- SS7 Backhaul Application 404
- Basic Setup 408
- Jumper Settings 410
- Line Rates/Line Lengths 412
- Single Channel POTS Cards 415
- Basic Configuration 422
- Power Supply 423
- Interface Connectors 426
- Input Power 427
- Install a Power Supply 429
- Remove a Power Supply 429
- Quad DS1 ADPCM Card 431
- Cross-Connects 439
- In this Chapter 443
- - CLI Commands 443
- - RJ-48 Connector 443
- State Description 452
- RS-232 Interface 457
- Bridging 457
- Router Performance 457
- Advanced Capabilities 457
- Frame Relay 458
- Filtering 458
- Security 458
- Connector Pinout 469
- TSR Card Jumpers 470
- At Power-up 471
- Normal Operation 471
- Port Set for Ethernet 471
- Port Set for RS-232 471
- V.35/.54 Card 473
- - Configured as DCE 475
- Accessories 476
- Receive Clock A → V 480
- Receive Clock B → X 480
- ← Local Loopback J 480
- ← Remote Loopback BB 480
- Low Speed Protection Card 481
- The Backup Card 483
- Protected Cards 483
- LED State Description 488
- Maintenance 489
- Software Loading 490
- Maintenance 491
- Using HyperTerminal 495
- Using Procomm 495
- Save Controller Configuration 497
- Load Controller Configuration 498
- Hot Swap Service Card 499
- APPENDIX 501
- Regulatory Approvals 502
- MIB Structure 504
- Enterprise MIB Support 505
- Router Enterprise MIB Support 506
- Public MIB Support 507
- SNMP Interface 508
- Router Public MIB Support 509
- Standard Traps 510
- Enterprise Traps 510
- Test Alarm 512
- Identify Alarm 512
- Loopback Tests 513
- Loopback Tests 514
- Display Alarms 514
- Clear Alarm 514
- Status and Performance 516
- DS1 Loopbacks 517
- DS1 Payload Loop 519
- Receiving DS-1 CSU Loop 520
- DS1 Equipment Loop 522
- V.35 Loopbacks 524
- V.35 Equipment Loop 526
- V.35/V.54 Loop 528
- V.54 Loop 529
- V.54 Equipment Loopback 530
- GLOSSARY 533
- Glossary 552
Relacionado con productos y manuales para Redes Carrier Access Network Device Axxius 800
Redes Carrier Access 770-0015 AM Manual de usuario
(250 paginas)
(250 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales